- F
- L
- E
- X
SS2100i single and dual box process gas analyzer is reliable in harsh environments
- F
- L
- E
- X
SS2100i-1 modified
- F
- L
- E
- X
SS2100i-1 modified
- F
- L
- E
- X
SS2100i-2
- F
- L
- E
- X
SS2100i-2 modified
SS2100i single and dual box process gas analyzer is reliable in harsh environments
Tổng quan về thông số kỹ thuật
-
Measuring principle
TDLAS
-
Measured variables
Concentration
Cell Pressure
Cell Temperature -
Hazardous area approvals
IECEx / ATEX / CNEx / KCs / CCOE / JPNEx Zone 1
Phạm vi ứng dụng
SS2100i gas analyzers accurately measure trace gas components (H2O, CO2, and H2S) using tunable diode laser absorption spectroscopy (TDLAS) technology. The analyzers require little maintenance and do not need recalibration or periodic replacement parts. SS2100i gas analyzers are certified for ATEX/IECEx Zone 1.
Gas analysis: ppb level measurement of H2O, ppm level measurement of H2O, H2S, and CO2, and % level measurement of H2S and CO2
Natural gas: production, storage, transportation, distribution
Refinery: hydrogen recycle, catalytic reforming, flaring, cracking
Gas processing: fractionation, sour/acid gas removal
LNG: liquefication, custody transfer
Petrochemical: cracking, caustic wash tower
Biomethane: custody transfer measurements of CO2, H2S, H2O
Lợi ích
Accurate, real-time measurements not hampered by wet-up (absorption) or dry-down (desorption)
Virtually maintenance free and reliable in harsh environments
Dependable with greater repeatability than surface-based sensors with NIST-traceable calibration
Analog and serial outputs for remote monitoring
Low cost of ownership, no consumables
Available for the following measurements: H2O, CO2, H2S
ATEX/IECEx Zone 1 certified
Lựa chọn Xpert
-
Sản phẩm chuyên dụng
- Dành cho các ứng dụng đòi hỏi cao
Công nghệ vượt trội
Đơn giản
Có thể thay đổi
-
Sản phẩm chuyên dụng
- Dành cho các ứng dụng đòi hỏi cao
Công nghệ vượt trội
Đơn giản
Có thể thay đổi
| Lựa chọn FLEX | Công nghệ vượt trội | Đơn giản |
|---|---|---|
Lựa chọn Fundamental Đáp ứng nhu cầu đo lường cơ bản |
Công nghệ vượt trội
|
Đơn giản
|
Lựa chọn Lean Xử lý dễ dàng các quy trình cốt lõi |
Công nghệ vượt trội
|
Đơn giản
|
Lựa chọn Extended Tối ưu hóa quy trình bằng công nghệ tiên tiến |
Công nghệ vượt trội
|
Đơn giản
|
Lựa chọn Xpert Làm chủ các ứng dụng khó khăn nhất |
Công nghệ vượt trội
|
Đơn giản
Có thể thay đổi |
Sản phẩm cũ
-
Measuring principle
TDLAS
-
Product headline
An advanced gas analyzer for hydrogen sulfide (H2S) measurement. The SS2100i uses tunable diode laser absorption spectroscopy (TDLAS) to determine the concentration of the analyte without coming into physical contact with the stream.
-
Channels
1
-
Analyte and measurement ranges
H2S (Hydrogen Sulfide):
0 to 10 ppmv
0 to 1000 ppmv
0 to 5000 ppmv
0 to 5% volume -
Measured variables
Concentration
Cell Pressure
Cell Temperature -
Ambient temperature range
-20 to 50°C (-4 to 122°F)
Optional (i-2 only): -10 to 60°C (14 to 140°F) -
Operating pressure range
Inlet Pressure: 140 to 350 kPa (20 to 50 psig)
Sample Cell: 800 to 1200 mbara or 950 to 1700 mbara (optional) -
Analyzer wetted materials
316L stainless steel
FKM O-Rings
Glass -
Power supply
120 or 240 VAC ± 10 %, 50 to 60 Hz; 300W
-
Communication
Analog Output: Two 4-20mA Isolated, 1200 ohms at 24 VDC max load (measurement value)
Analog Input: One 4-20mA Isolated, 1200 ohms at 24 VDC max load (process pressure)
Serial: RS232C and Ethernet
Protocol: Modbus Gould RTU or Daniel RTU or ASCII
Digital Outputs: 5, Concentration Alarm, General Fault, Validation Fail, Validation 1 Active, Validation 2 Active
Digital Inputs: 2, Flow Alarm, Validation Request -
Housing materials
Electronics: Copper-free Aluminum
Laser/Cell Enclosure: Copper-free Aluminum (i-2 only)
Sample System Enclosure: 304 or 316 stainless steel -
Hazardous area approvals
IECEx / ATEX / CNEx / KCs / CCOE / JPNEx Zone 1
-
Degree of protection
IP66
-
Product safety
CE
-
Metrological approvals
PAC China, Kazakhstan (i-1 only)
-
Measuring principle
TDLAS
-
Product headline
An advanced gas analyzer for moisture (H2O) measurement. The SS2100i uses tunable diode laser absorption spectroscopy (TDLAS) to determine the concentration of the analyte without coming into physical contact with the stream.
-
Channels
1
-
Analyte and measurement ranges
H2O (Moisture):
0 to 10 ppmv
0 to 100 ppmv
0 to 50 ppmv
0 to 5000 ppmv -
Measured variables
Concentration
Moisture Dew Point
Cell Pressure
Cell Temperature -
Ambient temperature range
-20 to 50°C (-4 to 122°F)
Optional (i-2 only): -10 to 60°C (14 to 140°F) -
Operating pressure range
Inlet Pressure: 140 to 350 kPa (20 to 50 psig)
Sample Cell: 800 to 1200 mbara or 950 to 1700 mbara (optional) -
Analyzer wetted materials
316L stainless steel
FKM O-Rings
Glass -
Power supply
120 or 240 VAC ± 10 %, 50 to 60 Hz; 300W
-
Communication
Analog Output: Two 4-20mA Isolated, 1200 ohms at 24 VDC max load (measurement value)
Analog Input: One 4-20mA Isolated, 1200 ohms at 24 VDC max load (process pressure)
Serial: RS232C and Ethernet
Protocol: Modbus Gould RTU or Daniel RTU or ASCII
Digital Outputs: 5, Concentration Alarm, General Fault, Validation Fail, Validation 1 Active, Validation 2 Active
Digital Inputs: 2, Flow Alarm, Validation Request -
Housing materials
Electronics: Copper-free Aluminum
Laser/Cell Enclosure: Copper-free Aluminum (i-2 only)
Sample System Enclosure: 304 or 316 stainless steel -
Hazardous area approvals
IECEx / ATEX / CNEx / KCs / CCOE / JPNEx Zone 1
-
Degree of protection
IP66
-
Product safety
CE
-
Metrological approvals
PAC China, Kazakhstan (i-1 only)
-
Measuring principle
TDLAS
-
Product headline
An advanced gas analyzer for carbon dioxide (CO2) measurement. The SS2100i uses tunable diode laser absorption spectroscopy (TDLAS) to determine the concentration of the analyte without coming into physical contact with the stream.
-
Channels
1
-
Analyte and measurement ranges
CO2 (Carbon Dioxide):
0 to 10 ppmv
0 to 1000 ppmv
0 to 5000 ppmv
0 to 5% volume
0 to 10% volume
0 to 20% volume -
Measured variables
Concentration
Cell Pressure
Cell Temperature -
Ambient temperature range
-20 to 50°C (-4 to 122°F)
Optional (i-2 only): -10 to 60°C (14 to 140°F) -
Operating pressure range
Inlet Pressure: 140 to 350 kPa (20 to 50 psig)
Sample Cell: 800 to 1200 mbara or 950 to 1700 mbara (optional) -
Analyzer wetted materials
316L stainless steel
FKM O-Rings
Glass -
Power supply
120 or 240 VAC ± 10 %, 50 to 60 Hz; 300W
-
Communication
Analog Output: Two 4-20mA Isolated, 1200 ohms at 24 VDC max load (measurement value)
Analog Input: One 4-20mA Isolated, 1200 ohms at 24 VDC max load (process pressure)
Serial: RS232C and Ethernet
Protocol: Modbus Gould RTU or Daniel RTU or ASCII
Digital Outputs: 5, Concentration Alarm, General Fault, Validation Fail, Validation 1 Active, Validation 2 Active
Digital Inputs: 2, Flow Alarm, Validation Request -
Housing materials
Electronics: Copper-free Aluminum
Laser/Cell Enclosure: Copper-free Aluminum (i-2 only)
Sample System Enclosure: 304 or 316 stainless steel -
Hazardous area approvals
IECEx / ATEX / CNEx / KCs / CCOE / JPNEx Zone 1
-
Degree of protection
IP66
-
Product safety
CE
-
Metrological approvals
PAC China, Kazakhstan (i-1 only)
-
-
Thông tin kĩ thuật (TI)
SS2100i-1 TDLAS Gas Analyzer Technical Information
-
Thông tin kĩ thuật (TI)
bản tiếng Anh - 01/2024New version available in EnglishSystem design and specifications for the SS2100i-1 TDLAS Gas Analyzer
EN VI 18/01/2024Ngôn ngữ:
Tiếng Anh
Phiên bản:
18/01/2024
Cỡ tập tin:
372.3 KB
Tên tập tin:
TI01669CEN_0223.pdf
-
-
-
Thông tin kĩ thuật (TI)
SS2100i-2 TDLAS Gas Analyzer Technical Information
-
Thông tin kĩ thuật (TI)
bản tiếng Anh - 01/2024New version available in EnglishSystem design and specification for the SS2100i-2 TDLAS Gas Analyzer
EN VI 19/01/2024Ngôn ngữ:
Tiếng Anh
Phiên bản:
19/01/2024
Cỡ tập tin:
425.6 KB
Tên tập tin:
TI01670CEN_0223.pdf
-
-
-
Hướng dẫn vận hành (BA)
SS2100-series TDLAS Gas Analyzer Sample Conditioning System Operating Instructions
-
Hướng dẫn vận hành (BA)
bản tiếng Anh - 02/2024New version available in EnglishCommissioning, operation, and maintenance details for the
SS2100-series TDLAS Gas Analyzer Sample Conditioning SystemEN VI 21/02/2024Ngôn ngữ:
Tiếng Anh
Phiên bản:
21/02/2024
Cỡ tập tin:
1.3 MB
Tên tập tin:
BA02337CEN_0123.pdf
-
-
-
Hướng dẫn vận hành (BA)
SS2100i-2 TDLAS gas analyzer Operating Instructions
-
Hướng dẫn vận hành (BA)
bản tiếng Anh - 06/2024New version available in EnglishCommissioning, operation, and maintenance details for the
SS2100i-2 TDLAS gas analyzerEN VI 26/06/2024Ngôn ngữ:
Tiếng Anh
Phiên bản:
26/06/2024
Cỡ tập tin:
6.5 MB
Tên tập tin:
BA02197CEN_0324.pdf
-
-
-
Hướng dẫn vận hành (BA)
TDL measurement cell Operating Instructions
-
Hướng dẫn vận hành (BA)
bản tiếng Anh - 08/2024New version available in EnglishOperation and maintenance details for TDLAS gas analyzer
measurement cellsEN VI 02/08/2024Ngôn ngữ:
Tiếng Anh
Phiên bản:
02/08/2024
Cỡ tập tin:
1.3 MB
Tên tập tin:
BA02188CEN_0224.pdf
-
-
-
Hướng dẫn vận hành (BA)
SS2100i-1 TDLAS Gas Analyzer Operating Instructions
-
Hướng dẫn vận hành (BA)
bản tiếng Anh - 03/2023New version available in EnglishCommissioning, operation and maintenance details for the SS2100i-1
TDLAS Gas AnalyzerEN VI 17/03/2023Ngôn ngữ:
Tiếng Anh
Phiên bản:
17/03/2023
Cỡ tập tin:
4.5 MB
Tên tập tin:
BA02189CEN_0223.pdf
-
-
-
Tham số thiết bị (GP)
FS 5.16 Description of device parameters
-
Tham số thiết bị (GP)
bản tiếng Anh - 10/2024New version available in EnglishExpert-level description and operational information
for device parametersEN VI 15/10/202417/09/2021Ngôn ngữ:
Tiếng Anh
Phiên bản:
15/10/2024
Cỡ tập tin:
2.5 MB
Tên tập tin:
GP01177CEN_0224.pdf
-
-
-
Tham số thiết bị (GP)
NS 5.14 Firmware Description of device parameters
-
Tham số thiết bị (GP)
bản tiếng Anh - 10/2024New version available in EnglishExpert-level description and operational information for
device parametersEN VI 15/10/2024Ngôn ngữ:
Tiếng Anh
Phiên bản:
15/10/2024
Cỡ tập tin:
2.6 MB
Tên tập tin:
GP01180CEN_0224.pdf
-
-
-
Hướng dẫn lắp đặt (EA)
TDLAS cell assembly mirror cleaning Installation Instructions
-
Hướng dẫn lắp đặt (EA)
bản tiếng Anh - 07/2024New version available in EnglishInstructions for cleaning the 0.1 m, 0.8 m, 8 m/28 m
measurement cell mirror for multiple TDLAS gas analyzersEN VI 29/07/2024Ngôn ngữ:
Tiếng Anh
Phiên bản:
29/07/2024
Cỡ tập tin:
382 KB
Tên tập tin:
EA01381CEN_0224.pdf
-
-
-
Hướng dẫn an toàn chống cháy (XA)
SS2100i-1 TDLAS Gas Analyzer Safety Instructions
-
Hướng dẫn an toàn chống cháy (XA)
bản tiếng Anh - 03/2023New version available in EnglishATEX/IECEx/UKEX: Zone 1
EN VI 17/03/2023Ngôn ngữ:
Tiếng Anh
Phiên bản:
17/03/2023
Cỡ tập tin:
1 MB
Tên tập tin:
XA02687CEN_0323.pdf
-
Chọn theo đề xuất của chúng tôi
-
-- selected coding-- selected label99.999,00<%label%>
-
Bạn muốn có nhiều lựa chọn hơn? Vui lòng sử dụng công cụ lựa chọn mã thiết bị để tiếp tục.
-
-- selected coding-- selected label99.999,00<%feature%>
-
<%label%>99.999,00
-
Bạn muốn có nhiều lựa chọn hơn? Vui lòng sử dụng công cụ lựa chọn mã thiết bị để tiếp tục.
-
Process Connection
-
<%label%>99.999,00
-
<%label%>99.999,00
-
-
<%feature%><%coding%><%label%>
- Bản vẽ CAD Bản vẽ CAD
- Bản vẽ CAD
-
Giá cho mỗi chi tiết
-
<%range%><%price%>
-
- Các add-on tùy chọn
Công cụ lựa chọn mã thiết bị
Thường mua kèm theo
Phụ kiện